Night Vision

How Night Vision works

All Starlight technology Night Vision Devices(NVD) consist of several main parts: an objective lens, an eyepiece, a power supply and an image intensifier tube (Photocathode Tube). Night vision devices gather existing ambient light (starlight, moonlight or infra-red light) through the front lens. This light, which is made up of photons, goes into a photocathode tube that changes the photons to electrons. The electrons are then amplified to a much greater number through an electrical and chemical process.The electrons are then hurled against a phosphorus screen that changes the amplified electrons back into visible light that you see through the eyepiece. The image will now be a clear green-hued amplified re-creation of the scene you are observing.  

 

                                          

 

                                                                                                     

Night Vision Devices Generations

A Night Vision Device can be either a  Gen 1+, Gen 2+ or Gen 3 generation units. These are differentiated by the image quality and amount of light amplication they produce, with Gen 1+ being the lowest and Gen 3 being the highest. Gen 1+ and Gen 2+ and Digital devices are avalible to the consumer market in Australia and Gen 3 and new FLAG (Film Less Auto Gated) sometimes called Gen 4 are for military and law enforcement use only.

Gen1+

Gen 1+ is currently the most popular type of night vision in the world. Utilizing the basic principles described earlier, a Gen 1+ unit will amplify the existing light several thousand times letting you clearly see in the dark. These units provide a bright and sharp image at a low cost, which is perfect, whether you are hunting, boating, observing wildlife, or providing security for your home. You may notice the following when you are looking through a Gen 1+ unit:

  • A slight high-pitched whine when the unit is on
  • The image you see may be slightly blurry around the edges, this is known as Geometric Distortion
  • When you turn a Gen 1+ unit off it may glow green for some time
  • These are inherent characteristics of a Gen1+ unit and are normal

Gen2+

Gen 2+ is primarily used for hunting, law enforcement or professional applications. This is because the cost of a Gen 2+ unit is consideralbly more than a Gen 1+. The main difference between a Gen 1+ and a Gen 2+ generation unit is the addition of a micro-channel plate, commonly referred to as a MCP. The MCP works as an electron amplifier and is placed directly behind the photocathode and consists of millions of short parallel glass tubes. When the electrons pass through these short tubes, thousands more electrons are released. This extra process allows Gen 2+ units to amplify the light many more times than Gen 1+ giving you a brighter and sharper image.

Gen 2+ IIT standard tubes are high quality with exceptional brightness and resolution. Each tube has a micro channel plate, multi-alkaline photocathode with built-in power supply.

Gen 2+ IIT Features:

  • Photo Cathode type: Multi-Alkali
  • Resolution from 40 to 45 lp/mm
  • Signal-to-Noise Ratio from 12 to 20
  • 5,000+ hour tube life

Gen 2+ CGTI IIT type of Image Intensifier tubes are engineered for significantly enhanced performance over current Gen2+ IITs. The CGTI IIT is a Multi-Alkali compact 18mm format MCP Image Intensifier. Highlights of the CGT specifications are typical SNR of 16-22 and resolution of 45-54 lp/mm. CGT IITs are sensitive in a wide spectral band and thus provide good contrast in all scene circumstances.

CGT IIT Features:

  • Photo Cathode type: Multi-Alkali
  • Resolution from 45 to 54 lp/mm
  • Signal-to-Noise Ratio from 16 to 22
  • 10,000-hour tube life

Night Vision Simulator 

Click image below to go to the interactive Night Vision Simulation from Photonis !!!

Infrared Illuminators

All Starlight scopes need some light to amplify. This means that if you are in complete darkness you could not see. Due to this we have a built in infra-red illuminator (IRI) on all of our scopes. Basically what an IRI does is throw out a beam of infra-red light that is near invisible to the naked eye but your NVD can see it. This allows you to use your scope even in total darktness. The IRI works like a flashlight and the distance you can see with it will be limited. We do use the most powerful eye-safe illuminator on the market. This allows our IRI to extend out to 100 yards However, because of the power at a short distance the IRI may cover only 40-60% of the viewing area.

 

How far you can see

There are many different variables that can affect the distance you can see with a night vision device. First, what are you trying to see? Are you looking for another boat on the water or are you looking for a rabbit in the woods? The larger the object the easier it is to see. Plus, are you trying to see details (what we call recognition range) or are you just trying to see if something is there? Maybe you will just see the movement, but won’t be able to determine 100% who or what it is. This is called “detection range”.

A second variable is lighting conditions. The more ambient light you have (starlight, moonlight, and infrared light) the better and further you will be able to see. You can always see further on a night where the moon and stars are out, than if it is cloudy and overcast. We typically state that you can tell the difference between a male and a female or a dog and a deer at about 75 to 100 yards. However, if you were looking across an open field and there was a half moon out you could see a barn or a house 500 yards away.

Remember, that the purpose of an NVD is to see in the dark not necessarily at a long distance like a binocular.

 

 

Digital  

 

Gen 1  

 

Gen 2  

 


 

 

WPT   

 

Gen 3  

 

Gen 4